A 3.85 mm iron walked down a 75 mm stitch line runs out of room after 19 gaps. The last hole lands 1.85 mm short of the corner: too close to skip, too far to call it the corner. That gap, on a card case or a wallet, is the thing a buyer’s eye goes to first, because a stitch line that misses its corner looks like a stitch line that was guessed.
Marcellino NY Bench Tool No. 3
Stitch Spacing Rulers: Free Printable PDF
⬇ DOWNLOAD THE BENCH TOOL (PDF)3 pages · US Letter, print at 100% · eleven true-size rulers, corner landing table, bench notes
The fix is arithmetic done before the iron touches the leather. The free Marcellino NY Bench Tool No. 3: Stitch Spacing Rulers gives eleven true-size rulers to lay out holes on paper or leather, and a table that does the corner arithmetic for the common irons.
What the rulers are
Each ruler is a strip with a slanted mark at every hole centre, numbered every ten holes. The slant follows the angle of a diamond iron, so the marks read like the holes they stand for. Two pages carry eleven rulers in total.
Seven are metric pitches: 2.7, 3.0, 3.38, 3.85, 4.0, 5.0 and 6.0 mm. The European iron sizes on that list match the Amy Roke pricking iron table at Rocky Mountain Leather Supply, which gives 3.85 mm as 6.6 stitches per inch, 3.38 mm as 7.5, 3.0 mm as 8.5 and 2.7 mm as 9.4. The other four rulers are 5, 6, 7 and 8 stitches per inch, the steps on Tandy’s Craftaid stitching guide, drawn at their exact metric pitch: 5.08, 4.23, 3.63 and 3.18 mm.
Inch and metric pitches do not line up neatly. Seven stitches per inch is 3.63 mm, which falls between the 3.38 and 3.85 mm irons and matches neither. Lay out a 100 mm line with the 7 spi ruler and punch it with a 3.85 mm iron, and the iron runs out of holes about a stitch and a half early: 27.5 gaps planned, 26 punched. That is why the rulers come in both systems. Match the ruler to the iron’s real pitch, not to the closest-sounding name.
The point is to see a spacing before buying an iron, to lay out a curve where the iron won’t sit flat, and to mark holes on a pattern so the pattern carries its own stitch plan. A ruler does not replace an iron. It tells the iron where to go.
Why a “3 mm iron” is not always 3 mm
Pitch is the distance from one hole centre to the next, and it is the only number that matters for layout. Irons are not all labeled by it.
On a leatherworker.net thread about converting irons to stitches per inch, one member explains that Seiwa and Kyoshin Elle irons are “measured as the distance between the points,” which is the pitch. Craft Sha irons are measured as the distance between the prongs, and the same member says those numbers run half of the Seiwa and Kyoshin figures. Another member notes that Tandy diamond chisel sizing “refers to the size of the prong, not the space between prongs.”
So two irons both sold as 3 mm can make different stitches. Before using the rulers with an iron already on the bench, press the iron lightly into scrap, measure across ten holes, and divide by ten. That is the iron’s real pitch, and it picks the ruler.

Printing them true
A ruler that prints at 97 percent is worse than no ruler. Over 200 mm of stitch line, a 1 percent scaling error moves the last hole 2 mm, about half a stitch on a 4 mm iron.
Every page of the PDF carries a scale square that must measure exactly 1 inch and a bar that must measure 50 mm. Print at 100 percent, or “Actual size,” with any “fit to page” option off. Then check the square with a steel rule before cutting anything.
A second check is built into the rulers. Measure from hole 0 to hole 10 on any ruler and divide by ten: the 3.85 mm ruler should read 38.5 mm across ten holes. If it reads 37.5, the printer scaled the page.
Paper patterns benefit most. Prick the hole positions straight through the pattern with an awl while the ruler sits on its stitch line, and the pattern carries a permanent stitch plan. Every future copy cut from it starts with the corners already solved.
Cut each ruler out along its box. Card stock lasts longer than paper, and a strip of clear packing tape over the face keeps an awl from tearing the marks.
Landing a hole on every corner
Page 3 of the PDF holds the table that fixes the opening problem. The method is three steps:
1. Measure the stitch line between the two corner holes, centre to centre.
2. Divide by the iron’s pitch and round to the nearest whole number. That is the number of gaps.
3. Divide the length by that number. That is the spacing that lands on both corners.
For the 75 mm run, 75 ÷ 3.85 is 19.5, rounded to 19 gaps. The landing spacing is 75 ÷ 19, or 3.95 mm. Each gap grows by about a tenth of a millimetre, the shift adds up along the line, and both ends land square on the corners.
| Run | 3.0 mm iron | 3.38 mm iron | 3.85 mm iron | 4.0 mm iron |
|---|---|---|---|---|
| 40 mm | 13 gaps @ 3.08 | 12 gaps @ 3.33 | 10 gaps @ 4.00 | 10 gaps @ 4.00 |
| 75 mm | 25 gaps @ 3.00 | 22 gaps @ 3.41 | 19 gaps @ 3.95 | 19 gaps @ 3.95 |
| 100 mm | 33 gaps @ 3.03 | 30 gaps @ 3.33 | 26 gaps @ 3.85 | 25 gaps @ 4.00 |
| 150 mm | 50 gaps @ 3.00 | 44 gaps @ 3.41 | 39 gaps @ 3.85 | 38 gaps @ 3.95 |
The full table runs from 25 to 300 mm and adds the 5 mm iron.
Some runs need almost nothing. A 100 mm line on a 3.85 mm iron takes 26 gaps at 3.846 mm, a change of four thousandths per hole. Short runs move the most, because the leftover is shared between fewer gaps: 40 mm on a 3.85 mm iron becomes 10 gaps at a full 4.00 mm.

Doing it with the iron in hand
A table gives the spacing. The iron still has to hit it, and makers disagree about how.
Weaver Leather Supply’s hand-sewing guide handles corners with two tools: place the first tine of a 2-tine chisel in the last hole, mark where the next hole goes, then punch it with a single-tine chisel, and repeat to the next straight edge. On a leatherworker.net thread about stitching that won’t line up at corners, the methods split three ways. One maker rolls the iron down the line like dividers to preview where the last hole falls, then varies the gap slightly over two or three stitches, and at a round corner stops one stitch short and makes the corner hole with a scratch awl. Another punches from the corners toward the middle and spaces the last few holes by eye. A third starts at the centre and works out both ways so any mismatch splits evenly, unless the stitching is partly hidden, in which case he starts from the end people will look at.
All three are adjustments made in the leather. The ruler moves that adjustment onto paper, where a mistake costs nothing. Mark the corner holes first, set the ruler between them, and adjust before a single hole is punched.
Not every maker wants the extra step. On thick bridle leather, makers who punch every hole by hand, as in the video above, often work by eye and by feel, and a printed strip adds a step. For a one-off briefcase gusset that is true. For a pattern that will be cut fifty times, a stitch plan drawn once and marked on the pattern pays for itself by the third copy.
Distance from the edge
Spacing along the line is one measurement. Distance from the edge is the other, and the rulers leave it alone. Weaver’s guide sets the groover to 1/8 inch, and its stitch groover guide gives 1/8 to 3/16 inch as common for most leathercraft projects. Set the line first with a groover or wing dividers, as covered in Marking a Stitch Line With Wing Dividers, then lay the ruler on it.
Tight curves need their own handling, since a long iron bridges a curve instead of following it. Stitching Tight Curves and Corners in Thick Leather covers that, and the rulers help there too: bend a paper ruler around the curve and the marks show exactly where a 2-prong or single-prong iron has to go.

Marcellino NY Bench Tool No. 3
Stitch Spacing Rulers: Free Printable PDF
⬇ DOWNLOAD THE BENCH TOOL (PDF)3 pages · US Letter, print at 100% · eleven true-size rulers, corner landing table, bench notes
Sources
- Rocky Mountain Leather Supply, Amy Roke pricking irons (pitch and spi): https://www.rmleathersupply.com/products/amy-roke-pricking-irons
- Tandy Leather, Craftaid stitching guide: https://tandyleather.ca/collections/projects/products/craftaid-stitching-guide
- mm to spi for pricking irons, leatherworker.net: https://leatherworker.net/forum/topic/55198-mm-to-spi-for-pricking-irons
- Weaver Leather Supply, how to hand sew leather: https://www.weaverleathersupply.com/pages/how-to-hand-sew-leather
- Weaver Leather Supply, how to use a stitch groover: https://www.weaverleathersupply.com/pages/how-to-use-a-stitch-groover-a-leathercraft-essential-explained
- Stitching not lining up at corners, leatherworker.net: https://leatherworker.net/forum/topic/69229-stitching-not-lining-up-at-corners
- Video: Marcellino NY Briefcase Maker on YouTube, https://www.youtube.com/watch?v=bQWo7edVaN8
You might also like
- Punching Stitch Holes in Thick Bridle Leather
- Diamond Chisels and French Chisels
- Marking a Stitch Line With Wing Dividers
- Stitching Tight Curves and Corners in Thick Leather




